Skip to content

Downspouts

Fiberglass Downspouts and Elbows

Round and square fiberglass downspout systems that match the gutter in material as well as in color, with the elbows and connectors required to complete a run.

FiberGutter square fiberglass downspout

System Overview

One Material From Roof to Ground

A gutter that cannot corrode loses much of that advantage if the water is then carried by a metal downspout that can. FiberGutter downspouts are fiberglass, so the exposed system behaves as one material.

3"

Nominal size

Round and square

10'

Standard length

Supplied in white

White

Supplied finish

Paintable to match

Round System

3 Inch Plain Round

Part: DSPR-10

3" Plain Round Fiberglass Downspout

10' length · White

Part: DSPR-EL75

3" Plain Round Fiberglass Downspout Elbow

Round profile

Part: FDSTAB-1

3" Plain Round Downspout Connecting Sleeve

Joins round sections

Part: DSHGRD-3

3" Plain Round Downspout Bracket

Wall bracket

The plain round profile is the traditional leader shape and is the usual choice on historic and classical elevations, where a round line is consistent with the rest of the detail.

Square System

3 Inch × 3 Inch Square

Part: DSSQ-10

3" × 3" Square Fiberglass Downspout

10' length · White

Part: DSSQ-EL75

3" Square Fiberglass Downspout Elbow

Square profile

Part: FDSTAB-2

3" Square Downspout Connecting Sleeve

Joins square sections

Part: DSHDSS-3

3" × 3" Square Downspout Bracket

Wall bracket

The square profile suits crisper, more contemporary elevations and reads well where the fascia, trim and columns are square in section.

Compatibility

Components Required to Complete a Run

A downspout run is more than the tube. These are the parts that connect it to the gutter and finish it.

SCH40 PVC Outlet

An SCH40 PVC outlet that directs water from the gutter into the downspout. Bonded into the gutter with GutterGlue.

Downspout Brackets

Brackets secure the downspout to the wall. Available as DSHGRD-3 for the round downspout and DSHDSS-3 for the square downspout.

GutterGlue and 2P-10

GutterGlue is the permanent structural adhesive used at outlets, sleeves, seams and end caps. 2P-10 is a fast-setting adhesive used to hold a joint while GutterGlue cures.

Paint and Finish

Downspouts are supplied in white. The published guidance is to sand the assembly with 80 grit to knock off the gloss, wipe with acetone or mineral spirits, then apply two coats of acrylic latex paint.

Downspouts should discharge to a location that carries water away from the foundation. Confirm the discharge point during layout rather than after the run is installed.

Selection

Choosing Round or Square

Both profiles are 3 inch nominal and carry the same water. The decision is architectural.

ConsiderationRound (DSPR)Square (DSSQ)
Architectural characterTraditional, classical, historicContemporary, crisp, modern
Pairs well withRound leaders, ornate trim, restorationSquare fascia, square columns, modern elevations
Nominal size3 inch3 inch × 3 inch
Standard length10 feet10 feet
ElbowDSPR-EL75DSSQ-EL75
Connecting sleeveFDSTAB-1FDSTAB-2
Wall bracketDSHGRD-3DSHDSS-3

Documentation

Installation Instructions

The downspout instructions cover outlet cutting, bonding and elbow placement.

Downspout Questions

Fiberglass Downspout FAQ

What downspout sizes are available?

Fiberglass downspouts are available in a 3 inch plain round profile and a 3 inch by 3 inch square profile. Both are supplied in 10 foot lengths in white, with matching elbows and connectors for each shape.

Should I use round or square downspouts?

Both are 3 inch nominal and carry the same water. The choice is architectural: round reads as a traditional leader and suits historic and classical elevations, while square reads as a crisper, more contemporary line and aligns visually with square fascia and trim.

What elbows are available?

Each system has a matching elbow: DSPR-EL75 for the round downspout and DSSQ-EL75 for the square downspout. Elbows are used at the top and bottom of a run to transition from the outlet to the wall and from the wall to the discharge point. Confirm the angle required for a specific layout with our team before ordering.

How do downspout sections join?

Sections join with a dedicated connecting sleeve: FDSTAB-1 for the 3 inch round downspout and FDSTAB-2 for the 3 inch square downspout. Elbows and sleeves are bonded with GutterGlue.

Are downspout brackets required?

Yes. The downspout is secured to the wall with brackets. Brackets are available as DSHGRD-3 for the round downspout and DSHDSS-3 for the square downspout. Bracket spacing for a specific run is set by the installation instructions.

How does the downspout connect to the gutter?

Through the SCH40 PVC outlet, which is bonded into the gutter with GutterGlue. Our downspout installation instructions cover the sequence in detail.

Are the downspouts fiberglass or metal?

The downspouts, elbows and connectors are fiberglass, so the entire exposed system shares the same material behavior as the gutter: it does not absorb water, does not corrode, and accepts paint.

Next step

Need Downspouts With Your Order?

Downspouts, elbows and connectors are quoted alongside the gutter so the whole system ships together.